LAHAR
KNOWLEDGE CENTER
LAHAR-30
TECH SPECS
SPECIFICATIONS
KEY ATTRIBUTES
- Bore Size: 30 Caliber
- Construction: 17-4 Stainless Steel, Inconel
- Finish: High Temperature Cerakote
- Mount Compatibility: 1 3/8x24 TPI
FEATURES
- Compatible with 5.56x45NATO and up to 300 Win Mag
- No minimum barrel length restrictions
- Full-auto rated
- Modular mounting interface
- Lifetime Manufacturers Warranty
SOUND DATA
Note: Sound test results are influenced by several different variables including location, ammunition, environmental conditions, host firearm, and more. These sound readings were gathered from the shooter's ear utilizing industry-standard sound reading equipment and factory-new ammunition.
KEY ATTRIBUTES
- Bore Size: 30 Caliber
- Construction: 17-4 Stainless Steel, Inconel
- Finish: High Temperature Cerakote
- Mount Compatibility: 1 3/8x24 TPI
FEATURES
- Compatible with 5.56x45NATO and up to 300 Win Mag
- No minimum barrel length restrictions
- Full-auto rated
- Modular mounting interface
- Lifetime Manufacturers Warranty
SOUND DATA
Note: Sound test results are influenced by several different variables including location, ammunition, environmental conditions, host firearm, and more. These sound readings were gathered from the shooter's ear utilizing industry-standard sound reading equipment and factory-new ammunition.
LAHAR
INSTALLATION
Other notes on installation here:
Your suppressor will come with either a direct thread or Mantle QD mount installed. To remove your mount, use the supplied wrench and turn the mount counterclockwise. When installing either a direct thread adapter or Mantle QD mount onto your Lahar-30 suppressor, first ensure that all threaded surfaces are clear of any debris and apply a liberal amount of anti-seize to your threads before installation. Thread your mount by hand into the rear of the Lahar suppressor and turn clockwise until tight. Snug utilizing the supplied wrenches.
BEFORE USE
Before using your suppressor—ensure that it is properly installed to the host firearm and has been checked for concentricity using a properly sized alignment rod.
The use of an alignment rod will help ensure concentricity between your host firearms bore and the bore of your suppressor. Proper concentricity is important as it will minimize your chances of a baffle strike and damage to your suppressor. If your alignment rod makes contact with any portion of the suppressor do not attempt to fire with the suppressor attached as it will likely result in a baffle strike.
*Note: Alignment rods are caliber specific. Ensure you are using the correct size alignment rod for your host firearms bore.
CARE & USAGE
When using the Lahar-30 it is important to ensure it is snuggly attached to the host firearm. This is especially important when using a direct thread adapter as direct thread suppressors will walk themselves loose over time. A loose suppressor can often result in a baffle strike and permanent damage to the suppressor. Your suppressor will become hot during firing. Before touching/handling your suppressor ensure it has returned to the ambient air temperature and wear a heat resistant glove.
COMPATIBILITY
Caliber Compatibility: 5.56X45 NATO – 300 WIN
Common calibers include: 5.56x45 NATO, 300 Blackout, 6mm ARC, 6.5 Grendel, 6.5 Creedmoor, 308 WIN, 7.62X51, 300 WIN.
*Note: The Lahar 30 is compatible with Combloc calibers such as 7.62x39 and 5.45x39. It is extremely important to ensure thread concentricity when using a suppressor with these calibers as AK-47/AKM pattern rifles frequently have non-concentric bores. Do not use corrosive ammunition with a Lahar-30 suppressor.
MAINTENANCE
Your Lahar-30 Suppressor requires very little cleaning and maintenance due to the nature of centerfire rifle suppressors. A light amount of oil on the exterior of your suppressor will help protect its finish from moisture damage.
Note: Do not soak your suppressor in solvent as it can result in finish damage. Test any oil or solvents on a small area of surface to avoid unintentional finish damage. If using a Mantle Quick Detach system, ensure that the mounting surface of your muzzle device is clear of any fouling buildup or debris.
The internals of your Lahar-30 suppressor do not require any cleaning or maintenance under normal circumstances.
Do not insert any foreign objects including bore cleaning patches into your suppressor.
LAHAR
GENERAL QUESTIONS
The Lahar-30 is rated for centerfire rifle cartridges no larger than .30 caliber up to .300 Winchester Magnum.
Yes, the Lahar-30 has no minimum barrel length requirements.
No, this will result in drastically accelerated fouling and a reduction in sound performance.
Yes. BUT you should first ensure that your muzzle threads are concentric. AK47/AKM barrels are notoriously non-concentric and may cause a baffle strike.
Yes. The Lahar-30 still provides amazing sound and flash reduction even when used with calibers smaller than .30.
The Lahar-30 utilizes 1-3/8x24 mount threads. This means any direct thread or quick detach mount utilizing these common threads will fit the Lahar-30.
POI shift can depend on several different variables such as platform and barrel length/profile. When used in conjunction with a Mantle Quick Detach system you can expect consistent POI shift between installations.
No. The Lahar-30 is fully welded. Centerfire rifle suppressors require little to no cleaning for the life of the suppressor.
Yes. The Lahar-30 is rated for fully automatic fire.
The body of the Lahar-30 features a high-temperature Cerakote finish.
Yes. Heat cycling to extreme temperatures over time can cause your suppressor to change in color.
No. Your Mantle compatible muzzle device should be installed with shims.
Only when using the Mantle Quick Detach mount on your Lahar-30.
No, the Mantle Quick Detach mount is ONLY compatible with muzzle devices specifically designed to work with a Mantle mount.
LIFETIME MANUFACTURER WARRANTY
We provide a lifetime warranty against manufacturing defects and damage caused by the normal use of our products. Aero Precision LLC will repair or replace any products that is has manufactured, sold, or distributed. This warranty does not cover defects or damage that are not the result of “normal use,” as determined by Aero Precision LLC in its full discretion, including but are not limited to defects and damage resulting from modification of the product, neglect or abuse of the product, improper transportation of the product, improper maintenance of the product, use of defective or improper ammunition, failure to follow the instructions in the product manual, use of the product with incompatible components, and criminal activity. To make a warranty or repair inquiry, contact Aero Precision’s customer service team by visiting aeroprecisionusa.com/contact and submitting a form. DO NOT send or ship products to Aero Precision for repair or replacement without first receiving authorization from Aero Precision’s customer service team. Failure to follow these instructions may void this warranty at Aero Precision’s discretion.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, CONDITIONS AND REPRESENTATIONS, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED CONDITION, REPRESENTATION OR WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER OR USER OF THE PRODUCT, AND AERO PRECISION LLC SHALL NOT BE LIABLE FOR AN ALLEGEDLY DEFECTIVE OR DAMAGED PRODUCT EXCEPT TO REPAIR OR REPLACE IT IN ACCORDANCE WITH THIS WARRANTY. IN NO EVENT, TO THE EXTENT PERMITTED BY LAW, SHALL AERO PRECISION LLC BE LIABLE FOR CONSEQUENTIAL, CONTINGENT, INCIDENTAL, INDIRECT OR SPECIAL DAMAGES CAUSED OR ALLEGED TO BE CAUSED IN WHOLE OR IN PART BY THE NEGLIGENCE, TORT, STRICT LIABILITY, BREACH OF CONTRACT, BREACH OF WARRANTY, OR BREACH OF DUTY OF OR BY AERO PRECISION LLC.
DISCLAIMERS
When using a firearm, always adhere to the 4 rules of firearms safety:
- Treat every firearm as if it is loaded.
- Always keep your firearm pointed in a safe direction.
- Keep your finger off the trigger until you have acquired a proper sight picture and are ready to fire.
- Be aware of your target and what is behind it.
- The first round fired through your cold suppressor will be marginally louder than sequential rounds fired. This is caused by the oxygen present in your suppressor before firing. Once this oxygen has been displaced from the suppressor during firing you will experience optimal sound performance.
- When using your suppressor it will retain heat when fired. This can result in very hot surface temperatures when firing.
- Do not touch your suppressor if it is hot as this will result in burns.
- Check Proper Alignment before firing.
- Do not use frangible, tracer, unjacketed, or corrosive ammunition in a Lahar-30 suppressor. Only use factory new ammunition from a reputable manufacturer.
